1 st generation crank shaft

Chris Burgess chris at chrisburgess.com
Thu Jun 3 22:08:16 PDT 2010


So why would one want to run a 1st gen crank over a 2nd gen crank assuming
its in a 2nd gen set of cases?

-Chris

p.s. I hope this pushed up my monthly bit numbers. :)

On Thu, Jun 3, 2010 at 10:06 PM, KC Gager <kc at brgracing.com> wrote:

> The great Z has spoken..... it's good he's around
>
> The Home of A Sickness for Quickness
> K.C.  Owner of BRG Racing Products and Dyno Services
> kc at brgracing.com
> Shop # 925-680-2560
> Toll Free # 1-877-ride-brg
> Address
> 110 2nd Ave South Unit D 12
> Pacheco Ca 94553
> AFM's 650 Twins Championship '08\'09 with Wil Fox
> AFM's Formula IV Class second place '09 with Wil Fox
> AFM's Formula Pacific #1 plate, '07\'08 with Dave Stanton
> AFM's 650 Twins Championship '07 with Jeff Hagan
> AFM's Formula IV Class Championship '07 with Jeff Hagan
> AFM's 650 Twins Second Place '06 with Dave Civiello
> AFM's 600 Superbike Championship '05 with Chris Siglin
> AFM's Open Production Championship '04 with Chris Siglin
> AFM's 650 Twins Championship '02 with Woody Woodward
> AFM's 500 Twins second place '99 with Simon Forder
> AFM's 500 Twins Championship '98 with Simon Forde
>
> -----Original Message-----
> From: sv650-bounces at micapeak.com [mailto:sv650-bounces at micapeak.com] On
> Behalf Of zoran
> Sent: Thursday, June 03, 2010 8:06 PM
> To: Suzuki SV650 Mailing List
>  Subject: Re: 1 st generation crank shaft
>
> Difference is that 2nd gen has grove for oil in one of main journals and
> trust bearing is built in to crank. In other words 2nd gen crank does not
> use trust bearing.
> I have 2nd gen crank in my 1st gen motor right now.
>
>
> Thanks
>
> Zoran Vujasinovic
> Twin Works Factory
> 775-786-4881
> www.twfracing.com
>
> ----- Original Message -----
> From: "Dan Chrystal" <dchrysta at columbus.rr.com>
> To: "Suzuki SV650 Mailing List" <sv650 at micapeak.com>
> Sent: Thursday, June 03, 2010 8:02 PM
> Subject: Re: 1 st generation crank shaft
>
>
> > When I compared them this morning they looked close, but seemed to have
> > some
> > subtle differences, is it a drop in, just follow the end play measurement
> > per the 1 st gen manual? Anything else to watch for?
> >
> > Thanks,
> >
> > Dan
> >
> > On Thu, Jun 3, 2010 at 10:43 PM, zoran <zv30 at sbcglobal.net> wrote:
> >
> >> They are, you can use either one in either motor.
> >>
> >>
> >> Thanks
> >>
> >> Zoran Vujasinovic
> >> Twin Works Factory
> >> 775-786-4881
> >> www.twfracing.com
> >> ----- Original Message ----- From: "Ernest Montague"
> >> <afm199 at earthlink.net
> >> >
> >> To: "Suzuki SV650 Mailing List" <sv650 at micapeak.com>
> >> Sent: Thursday, June 03, 2010 7:40 PM
> >> Subject: Re: 1 st generation crank shaft
> >>
> >>
> >>
> >>  Not really
> >>>
> >>> gen one can fit gen two with shims
> >>>
> >>>
> >>> On Jun 3, 2010, at 7:38 PM, Steve Robertson wrote:
> >>>
> >>>  I thought cranks were interchangeable, no?
> >>>>
> >>>>  I need a 1 st generation crank shaft, I have a good second generation
> >>>>> crank shaft with rods. Anyone have one they would like to trade?
> >>>>> Dan
> >>>>>
> >>>>
> >>>>
> >>>
>
>


-- 
WERA #104
OMRRA #104
WMRRA #104
http://www.burgiracing.com
http://www.sponsorhouse.com/members/thatman

2010 Sponsors
Vortex Racing - http://www.vortexracing.com
Motorex - http://www.motorex.com


More information about the SV650 mailing list